Search Results

Despite the tough environmental conditions facing electronic systems in commercial vehicles, electronics is gaining ground also in these applications. In the drive sector it improves the operation of the main and auxiliary drives, upgrades fuel efficiency and reduces emission pollutant levels. It enhances safety by preventing wheel spinning in braking and acceleration. Electronic displays reduce the number of single indications otherwise needed, thus making for more clarity in information for the driver and facilitating the driver's task. Self-diagnosing and integrated emergency operation (“limp home”) capabilities are to ensure availability, a factor of special importance in commercial vehicles. A data interface standardized as widely as possible would allow add-on systems to be coupled easily and flexibly.

Control of a car is lost, or considerably reduced, whenever one or more of the wheels exceed the stability limit during braking or accelerating due to excessive brake or drive slip. The problem of ensuring optimum stability, steerability and brake distance of a car during hard braking is solved by means of the well-known Anti-lock Braking System (ABS). The task to guarantee stability, steerability and optimum traction during acceleration, particularly on asymmetrical road surfaces and during cornering maneuvers, is being performed by the traction control system (ASR). Several means to provide an optimum traction control are described, e. g the control of engine torque by influencing the throttle plate and/or the ignition and/or the fuel injection.

Additional future requirements for automobiles such as improved vehicle dynamics control, enhanced comfort, increased safety and compact packaging are met by modern electrical steering systems. Based on these requirements the new functionality is realized by various additional electrical components for measuring, signal processing and actuator control. However, the reliability of these new systems has to meet the standard of today's automotive steering products. To achieve the demands of the respective components (e.g. sensors, bus systems, electronic control units, power units, actuators) the systems have to be fault-tolerant and/or fail-silent. The realization of the derived safety structures requires both expertise and experience in design and mass production of safety relevant electrical systems. Beside system safety and system availability the redundant electrical systems also have to meet economic and market requirements.

In recent times, the software portion and the complexity of software within automotive electronic control units have grown noticeably and continue to grow. In order to get a grip on the software complexity and the amount of customer-specific software variants, a modeling concept for a structured and easily extensible software architecture is needed. This concept should efficiently support the formation of variants and code reuse without increasing runtime and memory space overhead. In this paper, we present our approach to such a modeling concept: The object-oriented modeling concept OMOS and its application to signal conditioning of vehicle control systems.

This paper describes an ion current measurement system with a new, modified inductive ignition system and evaluates the detection quality for misfire and knock detection. The System uses an ignition circuit with adjustable spark duration limitation. The measurement circuit is located at the low tension side of the secondary ignition coil. Due to the fact that a lot of influencing factors on misfire detection have been investigated, the estimation of the signal-to-noise-ratio is possible as well as the detection of critical operation points. Results of a closed-loop knock control with ion current are presented and are compared with the structure borne noise method.

Two-dimensional Mie and LIEF techniques were applied to investigate the spray formation of a high pressure gasoline swirl injector in a constant volume chamber. The results obtained provide information on the propagation of liquid fuel and fuel vapor for different fuel pressures and ambient conditions. Spray parameters like tip penetration, cone angles and two new defined parameters describing the radial fuel distribution were used to quantify the fuel distributions measured. Simultaneous detection of liquid and vapor fuel was applied to study the influence of ambient temperature, injector temperature and ambient pressure on the evaporating spray.

A networking of control systems poses high challenges - in particular for guaranteeing its safety, reliability, and acceptance of the whole integrated system by the car user. CARTRONIC is an open architecture for networking the control systems of a vehicle. The organization of a network has to be set up systematically and with foresight to achieve the advantages of going beyond the sum of the components and to avoid mutual disturbance. Thus the cooperation does not only require well-defined interfaces, but also coordination of the control strategies in the individual components. Additionally, there is an increasing need for ensuring that safety risks are effectively minimized, and for ensuring that no degradation in performance from either a safety or environmental point of view might take place. The paper is focused on the safety-related aspect of CARTRONIC, the safety analysis. The output of the safety analysis is a Safety Architecture.

In a study using a single-cylinder engine a significant potential in fuel efficiency and emission reduction was found for stratified operation of a high pressure natural gas direct injection (DI) spark ignition (SI) engine. The control of the mixture formation process appeared to be critical to ensure stable inflammation of the mixture. Therefore, optical investigations of the mixture formation were performed on a geometric equivalent, optically accessible single-cylinder engine to investigate the correlation of mixture formation and inflammability. The two optical measurement techniques infrared (IR) absorption and laser-induced fluorescence (LIF) were employed. Mid-wavelength IR absorption appeared to be qualified for a global visualization of natural gas injection; LIF allows to quantify the equivalence ratio inside a detection level. While LIF measurements require complex equipment, the IR setup consists merely of a black body heater and a mid-wavelength sensitive IR camera.

Historically, whenever the automotive solutions’ state of art reaches a saturation level, the integration of new verticals of technology has always raised new opportunities to innovate, enhance and optimize automotive solutions. The predictive powertrain solutions using connectivity elements (e.g., navigation unit, e-Horizon or cloud-based services) are one of such areas of huge interest in automotive industry. The prior knowledge of trip destination and its route characteristics has potential to make prediction of powertrain modes or events in certain order and therefore it can add value in various application areas such as optimized energy management, lower fuel consumption, superior safety and comfort, etc.

In the Indian two-wheeler market, legislation and customers demand for a reduction of emissions and an increase of fuel efficiency. For two-wheelers with engine management systems, a cost-efficient approach for this trend exploits that the periodical fluctuation of the engine speed of single cylinder engines contains useful information about its operating conditions. The present article focuses on the quality of the estimation of combustion phasing and air-fuel ratio of a 125cc single cylinder motorcycle engine, obtained from the evaluation of these fluctuations. The robustness of an oxygen sensor-less port fuel injection system can be increased by using the estimated air-fuel ratio to adapt the parameters of the fuel injection algorithm.

The design of ABS- or vehicle control systems by means of computer simulation needs adequate tire models. Recordings of the wheel speed during ABS control show oscillations caused by the rapid pressure changes in the wheel brake cylinder. Investigations in lateral tire dynamics show a phase shift between the slip angle and the lateral tire force. These transients can not be explained by simulation if the usual stationary tire input-output behaviour is supposed. Thus the investigation of the oscillations requires a different approach to the modelling of the tire. In a first step measurements with an experimental car equipped with a computer for data acquisition and control and with various sensors - e.g. a Rotating Wheel Dynamometer - were carried out. The measurement results showed a correlation between the oscillations in the wheel speed and the braking force caused by the pressure pulses as well as high frequency oscillations in the lateral tire forces.

X-Domain describes the merging of different domains (i.e., braking, steering, propulsion, suspension) into single functionalities. One example in this context is torque-vectoring. Different goals can be pursued by applying X-Domain features. On the one hand, savings in fuel consumption and an improved vehicle driving performance can be potentially accomplished. On the other hand, safety can be improved by taking over a failed or degraded functionality of one domain by other domains. The safety-aspect from the viewpoint of requirements is highlighted within this contribution. Every automotive system being developed and influencing the vehicle safety must fulfill certain safety objectives. These are top-level safety requirements (ISO 26262-1) specifying functionalities to avoid unreasonable risk. Every safety objective is associated with an Automotive Safety Integrity Level (ASIL) derived from a Hazard Analysis and Risk Assessment (HARA).

In the low-cost segment for 2-Wheelers legislative, economic and ecologic considerations necessitate a reduction of the emissions and further improvement in fuel consumption. To reach these targets, the commonly used carburetors are being replaced by engine management systems (EMS). One option to provide these systems for acceptable and attractive system costs is to save a sensor device and to substitute its measure by an estimation value. In many motorcycles the rotor of the vehicle's alternator is rigidly attached to the crankshaft. Therefore, the voltage and current signals of the alternator contain information about the engine's speed, which can be retrieved by evaluating these electric signals. After further processing of this information inside the electronic control unit (ECU), the absolute crankshaft position can be obtained. A high-resolution speed signal without mechanical distortions like tooth errors is gained, whose signal quality equals the one of a common speed sensor.

The introduction of stricter emission legislation and the demand of increased power for small two-wheelers lead to an increase of technical requirements. Especially the introduction of liquid-cooling over air-cooling allows the introduction of higher compression ratios, which improves power output as well as thermodynamic efficiencies and thereby fuel consumption. But an increase in compression ratio also introduces further challenges during transient behavior especially close to idling. In order to keep the two-wheeler specific responsiveness of the vehicle, the overall rotational inertia of the engine must be kept low. But the combination of low inertia and high compression ratio can lead to a stalling of the engine if the throttle is opened and closed very quickly in idle operation. The fast opening and closing of the throttle is called a throttle blip.

VDC is a new active safety system for road vehicles which controls the dynamic vehicle motion in emergency situations. From the steering angle, the accelerator pedal position and the brake pressure the desired motion is derived while the actual vehicle motion is derived from the yaw rate and the lateral acceleration. The system regulates the engine torque and the wheel brake pressures using traction control components to minimize the difference between the actual and the desired motion. Included is also a safety concept which supervises the proper operation of the components and the software.

This paper shows that the functional integration of Electronic Throttle Control (ETC) into the engine control strategy allows improvements of emissions and fuel economy without making compromises in respect of driveability. A cost effective way for realizing ETC is the integration of the control electronics into the engine control unit (ECU). The paper describes the consequences of such an integration for the ECU hardware and software. Special attention is given to the ETC related safety aspects. Another chapter discusses different technologies for the throttle actuator drive. This is followed by a brief description of a suitable control strategy for a throttle actuator. Finally the paper gives also an overview about current status and development trends of accelerator pedal sensors necessary for ETC.

This study focuses on evaluation of various fuels within a conventional gasoline internal combustion engine (ICE) vehicle and the implementation of advanced emissions reduction technology. It shows the robustness of the implemented technology packages for achieving ultra-low tailpipe emissions to different market fuels and demonstrates the potential of future GHG neutral powertrains enabled by drop-in lower carbon fuels (LCF). An ultra-low emission (ULE) sedan vehicle was set up using state-of-the-art engine technology, with advanced vehicle control and exhaust gas aftertreatment system including a prototype rapid catalyst heating (RCH) unit. Currently regulated criteria pollutant emission species were measured at both engine-out and tailpipe locations. Vehicle was run on three different drive cycles at the chassis dynamometer: two standard cycles (WLTC and TfL) at 20°C, and a real driving emission (RDE) cycle at -7°C.